Lumion Support Center

Support for unlicensed users => Post here if you have not got Lumion yet => Topic started by: [email protected] on February 25, 2020, 01:18:54 pm

Title: [Awaiting reply] Lumion 10.0.2
Post by: [email protected] on February 25, 2020, 01:18:54 pm
Sehr geehrte Damen und Herren!


Ich habe Probleme mit OPRM-Lumion, und zwar folgendes:

Lumion bleibt bei der Materialvergabe sehr oft stecken. D.H. Wenn ich ein Material einfüge oder kopiere dauert es zwischen 8 und 25 Sekunden bis die Bauteile die Materialtextur übernehmen. Rechts oben, wo der Dateiverweis ist, steht dann oftmals als Zusatz „keine Rückmeldung“

Danke
Mit freundlichen Grüßen
Ralf

Title: Re: Lumion 10.0.2
Post by: Morten on February 25, 2020, 01:30:15 pm
Google Translate:

Quote
Dear Sir or Madam!

I have problems with OPRM-Lumion, the following:

Lumion very often gets stuck during material allocation. D. H. When I paste or copy a material, it takes between 8 and 25 seconds for the components to adopt the material texture. At the top right, where the file reference is, there is often the addition "no feedback"

Thank you
Sincerely yours
R.
Title: Re: Lumion 10.0.2
Post by: Morten on February 25, 2020, 01:33:27 pm
Hi Ralf, I'm sorry to hear that.

The reason is usually that the material file is large and/or that the Documents folder is located on a drive with slow access speeds, e.g. a network drive.

1. Please open the Documents/Lumion 8.0/Library folder. There should be 4 model files for the model you're assigning materials to. What are the sizes of the 4 files?

2. Which drive is the Documents folder located on?

3. How much free space is there on the drive that the Documents folder is located on?

Thanks.
Title: Re: [Awaiting reply] Lumion 10.0.2
Post by: [email protected] on February 25, 2020, 05:17:16 pm
Hi there,

Answers to questions:

1. Attached 1(1).png
2. Lumion 10 ist am LAUFWERK C – Festplatte: HDD SATA - WD SSD M.2 (2280), 250 GB, S250G2X0C Black NVMe
Mein eigener Zusatz-Materialordner ist am LAUFWERK B – Festplatte: HDD SATA – SSD 2.5“, 480 GB, PNY CS900 SATA 3
Ich verwende teilweise Materialien aus meinem Zusatzordner – wie z.B. EGGER Dekorprogramm
3. Attached 7.jpg and 8.jpg

thanks
Ralf
Title: Re: [Awaiting reply] Lumion 10.0.2
Post by: Morten on February 25, 2020, 06:26:22 pm
Google Translate:

Quote
1. Attached 1 (1) .png
2.Lumion 10 is on LAUFWERK C - hard drive: HDD SATA - WD SSD M.2 (2280), 250 GB, S250G2X0C Black NVMe
My own additional material folder is on LAUFWERK B - hard drive: HDD SATA - SSD 2.5 “, 480 GB, PNY CS900 SATA 3
I sometimes use materials from my additional folder - such as EGGER decor range
3. Attached 7.jpg and 8.jpg

thanks
Ralf

Thanks a lot, Ralf.

The problem is that the material file (.MTT) is 0.8 GB.

That will take quite long to save/load.

1. Are you using any high-resolution texture files for your materials? Or just any texture files that are quite large?

2. If so, please try to re-save the textures in a compressed format, e.g. .JPG format and at lower resolutions (we recommend maximum 2048x2048 pixels for detailed materials).

Does this make the .MTT file smaller?